LIST OF ASTM STANDARDS 301 TO 400

ASTM    G 97-97(2013) : Standard Test Method for Laboratory Evaluation of Magnesium Sacrificial Anode Test Specimens for Underground Applications
ASTM    B 98/B 98M-13 : Standard Specification for Copper-Silicon Alloy Rod, Bar and Shapes
ASTM    G 98-02(2009) : Standard Test Method for Galling Resistance of Materials
ASTM    D 98-05(2013) : Standard Specification for Calcium Chloride
ASTM    A 99-03(2009) : Standard Specification for Ferromanganese
ASTM    C 99/C 99M-09 : Standard Test Method for Modulus of Rupture of Dimension Stone
ASTM    B 99/B 99M-11 : Standard Specification for  Copper-Silicon Alloy Wire for General Applications
ASTM    F 99-07(2011) : Standard Guide for  Writing a Specification for Flexible Barrier Rollstock Materials
ASTM    G 99-05(2010) : Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus
ASTM    A 100-07(2012) : Standard Specification for  Ferrosilicon
ASTM    B 100-13 : Standard Specification for Wrought Copper-Alloy Bearing and Expansion Plates and Sheets for Bridge and Other Structural Use
ASTM    G 100-89(2010)e1 : Standard Test Method for Conducting Cyclic Galvanostaircase Polarization
ASTM    E 100-10 : Standard Specification for ASTM Hydrometers
ASTM    G 101-04(2010) : Standard Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels
ASTM    B 101-12 : Standard Specification for Lead-Coated Copper Sheet and Strip for Building Construction
ASTM    A 101-04(2009) : Standard Specification for Ferrochromium
ASTM    G 102-89(2010) : Standard Practice for Calculation of Corrosion Rates and Related Information from Electrochemical Measurements
ASTM    A 102-04(2009) : Standard Specification for Ferrovanadium
ASTM    E 102/E 102M-93(2009) : Standard Test Method for Saybolt Furol Viscosity of Bituminous Materials at High Temperatures
ASTM    B 103/B 103M-10 : Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar
ASTM    G 103-97(2011) : Standard Practice for Evaluating Stress-Corrosion Cracking Resistance of Low Copper 7XXX Series Al-Zn-Mg-Cu Alloys in Boiling 6% Sodium Chloride Solution
ASTM    E 103-12 : Standard Practice for  Rapid Indentation Hardness Testing of Metallic Materials
ASTM    E 104-02(2012) : Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Solutions
ASTM    F 104-11 : Standard Classification System for Nonmetallic Gasket Materials
ASTM    F 105-72(2010) : Standard Specification for Type 58 Borosilicate Sealing Glass
ASTM    G 105-02(2007) : Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests
ASTM    B 105-05(2012) : Standard Specification for Hard-Drawn Copper Alloy Wires for Electric Conductors
ASTM    E 105-10 : Standard Practice for Probability Sampling Of Materials
ASTM    A 105/A 105M-13 : Standard Specification for Carbon Steel Forgings for Piping Applications
ASTM    G 106-89(2010) : Standard Practice for Verification of Algorithm and Equipment for Electrochemical Impedance Measurements
ASTM    B 106-08(2013) : Standard Test Methods for Flexivity of Thermostat Metals
ASTM    A 106/A 106M-14 : Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service
ASTM    F 106-12 : Standard Specification for  Brazing Filler Metals for Electron Devices
ASTM    B 107/B 107M-13 : Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire
ASTM    G 107-95(2008) : Standard Guide for Formats for Collection and Compilation of Corrosion Data for Metals for Computerized Database Input
ASTM    C 108-46(2013) : Standard Symbols for Heat Transmission
ASTM    A 108-13 : Standard Specification for Steel Bar, Carbon and Alloy, Cold-Finished
ASTM    G 108-94(2010) : Standard Test Method for Electrochemical Reactivation (EPR) for Detecting Sensitization of AISI Type 304 and 304L Stainless Steels
ASTM    B 108/B 108M-12e1 : Standard Specification for Aluminum-Alloy Permanent Mold Castings
ASTM    E 108-11 : Standard Test Methods for  Fire Tests of Roof Coverings
ASTM    C 109/C 109M-13 : Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
ASTM    G 109-07(2013) : Standard Test Method for Determining Effects of Chemical Admixtures on Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments
ASTM    F 109-12 : Standard Terminology Relating to Surface Imperfections on Ceramics
ASTM    A 109/A 109M-13 : Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
ASTM    E 110-10 : Standard Test Method for Indentation Hardness of Metallic Materials by Portable Hardness Testers
ASTM    C 110-11 : Standard Test Methods for  Physical Testing of Quicklime, Hydrated Lime, and Limestone
ASTM    G 110-92(2009) : Standard Practice for Evaluating Intergranular Corrosion Resistance of Heat Treatable Aluminum Alloys by Immersion in Sodium Chloride + Hydrogen Peroxide Solution
ASTM    G 111-97(2013) : Standard Guide for Corrosion Tests in High Temperature or High Pressure Environment, or Both
ASTM    B 111/B 111M-11 : Standard Specification for  Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock
ASTM    A 111-99a(2009) : Standard Specification for Zinc-Coated (Galvanized) “Iron” Telephone and Telegraph Line Wire
ASTM    E 111-04(2010) : Standard Test Method for Young’s Modulus, Tangent Modulus, and Chord Modulus
ASTM    E 112-13 : Standard Test Methods for Determining Average Grain Size
ASTM    F 112-00(2013) : Standard Test Method for Sealability of Enveloped Gaskets
ASTM    G 112-92(2009) : Standard Guide for Conducting Exfoliation Corrosion Tests in Aluminum Alloys
ASTM    C 113-02(2008) : Standard Test Method for  Reheat Change of Refractory Brick
ASTM    G 113-14 : Standard Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials
ASTM    D 113-07 : Standard Test Method for  Ductility of Bituminous Materials
ASTM    G 114-07 : Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service
ASTM    E 114-10 : Standard Practice for  Ultrasonic Pulse-Echo Straight-Beam Contact Testing
ASTM    B 114-07(2013) : Standard Test Method for Temperature-Resistance Constants of Sheet Materials for Shunts and Precision Resistors
ASTM    C 114-13 : Standard Test Methods for Chemical Analysis of Hydraulic Cement
ASTM    D 115-07(2012) : Standard Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation
ASTM    B 115-10 : Standard Specification for Electrolytic Copper Cathode
ASTM    C 115/C 115M-10E1 : Standard Test Method for Fineness of Portland Cement by the Turbidimeter
ASTM    G 115-10(2013) : Standard Guide for Measuring and Reporting Friction Coefficients
ASTM    F 116-12 : Standard Specification for Medical Screwdriver Bits
ASTM    B 116-95(2012) : Standard Specification for Figure-9 Deep-Grooved and Figure-8 Copper Trolly Wire for Industrial Haulage
ASTM    G 116-99(2010) : Standard Practice for Conducting Wire-on-Bolt Test for Atmospheric Galvanic Corrosion
ASTM    A 116-11 : Standard Specification for Metallic-Coated, Steel Woven Wire Fence Fabric
ASTM    D 116-86(2011) : Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications
ASTM    B 117-11 : Standard Practice for Operating Salt Spray (Fog) Apparatus
ASTM    C 117-13 : Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
ASTM    D 117-10 : Standard Guide for Sampling, Test Methods, and Specifications for Electrical Insulating Oils of Petroleum Origin
ASTM    G 117-13 : Standard Guide for Calculating and Reporting Measures of Precision Using Data from Interlaboratory Wear or Erosion Tests
ASTM    G 118-02(2007) : Standard Guide for Recommended Format of Wear Test Data Suitable for Databases
ASTM    C 118-11 : Standard Specification for  Concrete Pipe for Irrigation or Drainage
ASTM    C 118M-11 : Standard Specification for  Concrete Pipe for Irrigation or Drainage (Metric)
ASTM    F 118-13 : Standard Definitions of Terms Relating to Gaskets
ASTM    E 119-12a : Standard Test Methods for Fire Tests of Building Construction and Materials
ASTM    G 119-09 : Standard Guide for Determining Synergism Between Wear and Corrosion
ASTM    F 119-82(2008) : Standard Test Method for  Rate of Grease Penetration of Flexible Barrier Materials (Rapid Method)
ASTM    C 119-11 : Standard Terminology Relating to Dimension Stone
ASTM    G 120-01(2008) : Standard Practice for Determination of Soluble Residual Contamination in by Soxhlet Extraction
ASTM    D 120-14 : Standard Specification for Rubber Insulating Gloves
ASTM    C 120/C 120M-12 : Standard Test Methods of Flexure Testing of Slate (Breaking Load, Modulus of Rupture, Modulus of Elasticity)
ASTM    G 121-98(2010)e1 : Standard Practice for Preparation of Contaminated Test Coupons for the Evaluation of Cleaning Agents
ASTM    B 121/B 121M-11 : Standard Specification for  Leaded Brass Plate, Sheet, Strip, and Rolled Bar
ASTM    D 121-09a : Standard Terminology of Coal and Coke
ASTM    C 121/C 121M-09e1 : Standard Test Method for Water Absorption of Slate
ASTM    A 121-13 : Standard Specification for Metallic-Coated Carbon Steel Barbed Wire
ASTM    E 122-09e1 : Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process
ASTM    B 122/B 122M-11 : Standard Specification for  Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar
ASTM    G 122-96(2008) : Standard Test Method for Evaluating the Effectiveness of Cleaning Agents
ASTM    E 123-02(2012) : Standard Specification for Apparatus for Determination of Water by Distillation
ASTM    G 123-00(2011) : Standard Test Method for Evaluating Stress-Corrosion Cracking of Stainless Alloys with Different Nickel Content in Boiling Acidified Sodium Chloride Solution
ASTM    C 123/C 123M-12 : Standard Test Method for  Lightweight Particles in Aggregate
ASTM    A 123/A 123M-13 : Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
ASTM    D 123-13A : Standard Terminology Relating to Textiles
ASTM    B 124/B 124M-14 : Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
ASTM    E 124-94(2010) : Standard Specification for Weighing and Drying Apparatus for Microchemical Analysis

QUICK QUOTE

Get Your Quote from Our Materials Scientists within 4 Hours

    Full Name *

    Your Email ID *

    Phone *

    Company

    Testing Needed *

    OR

    EMAIL US

    OR

    CALL US

    USA
    Telephone :+1 770.823.5031
    Telephone:+1 404.918.8782

    INDIA
    Telephone : (0253) 2361782
    Mobile : +91 9552508782

    TESTING SERVICES

     

    [sp_faq category="19"]

      

    [sp_faq category="20"]
    [sp_faq category="21"]
    [sp_faq category="22"]

    Our Team

    Collaborate with us

    Get A Quote

    Our Services

    SEND US A REQUEST

    Need help or have a question? (0253) 2361782

    SEND US A REQUEST